Enerdrive ePOWER B-TEC 200Ah Lithium Battery, 40A DC2DC + 100A AC + 2600W Inverter & Simarine Best Choice

Enerdrive ePOWER B-TEC 200Ah Lithium Battery, 40A DC2DC + 100A AC + 2600W Inverter & Simarine, 5 Year Warranty.

Pack Includes:

• Enerdrive ePOWER B-TEC 200Ah Lithium Battery Only, EPL-200BT-12V-G2
• Enerdrive DC2DC Battery Charger – 12V 40A, EN3DC40
• Enerdrive ePOWER 100amp / 12v Smart Charger – Three Output, EN312100
• Enerdrive ePOWER 2600W 12V Pure Sine Wave Inverter with RCD & AC Transfer Switch, EN1226S-X
• Simarine Pico+ Display Panel Mount Black, SI-PICO-3
• Simarine Battery Shunt 300A 2 x Volt 2 x Resist 1 x Temp, SI-SC303
• Simarine by Enerdrive Quad Shunt Mod 4 x 50A Input Current & 1 x Relay Output 1A, SI-SCQ50

Enerdrive ePOWER B-TEC 200Ah Lithium Battery:

Enerdrive have released the new ePOWER B-TEC 200Ah Lithium Battery with new features including:

• BMS restart button for easy recovery
• RS485 communications port for advanced system integration
• Raised terminals for 360 degree cable connections
• Re-designed battery case for easy serviceability
• Battery box and straps INCLUDED – nothing more to buy!

 This Enerdrive lithium battery is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity.

Smart Phone Monitoring System:

The Enerdrive ePOWER B-TEC battery incorporates wireless Battery Monitoring Technology. By downloading the Android or Apple app to your smartphone or tablet device, you can monitor the following information;

• Battery Capacity
• Battery Voltage
• Battery Current (Amps)
• Battery State of Charge (SOC)
• Battery State of Health (SOH)
• Battery Status
• Individual Cell Voltage
• Battery Temperature
• Battery Cycles
• Battery Alarms
• Battery Event Information

Battery Management System:

This Enerdrive lithium battery is also equipped with an internal LiFePO4 Battery Management System (BMS) that can monitor and optimize each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery.

Size & Weight Savings:

Lithium v AGM Capacities;

• 200Ah Lithium = 360Ah AGM

(Based on standard depth of discharge for both Lithium (80%) and AGM (50%).

This Enerdrive lithium battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative.

The ePOWER B-TEC battery is perfect for camper trailers, 4WD’s (AUX battery), caravans, small water craft, low power communication sites or any other application that requires the use of a single deep cycle battery that meets the amp hour capacity.

With over 5 years of researching, designing and testing lithium batteries and the associated charging systems, Enerdrive are at the forefront of lithium battery systems in Australia. Enerdrive are the only Australian company that can supply a fully integrated self-branded energy system to suit your setup.

With over 1200 complete systems in operation Australia wide, Enerdrive is regarded as the leader in the field of lithium batteries and energy systems for Mobile, Marine and Remote applications.

Please Note: This Enerdrive lithium battery is capable to be paralleled to a second ePOWER B-TEC lithium battery. For maximum performance and lifespan of your lithium battery, no more than 2 batteries should be connected together to increase your overall capacity. Overall loads when paralleled should not exceed the current limits of a single batteries BMS.

Enerdrive ePOWER 12V 40A DC to DC Battery Charger:

Enerdrive ePOWER 12V 40A DC to DC Battery Charger designed to meet the rugged demands of Australian conditions and delivering multiple source charging for DC systems.

The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller.

PRO TIP: Common accessories to go with this DC to DC charger are the 60Amp & 70Amp breakers, also the 3 pre-wired & fused charging cables. These are available in the Accessory List above to add as optional extras, please see the product manual & drawings for the connection.

12V 40A DC2DC Battery Charger Features

• Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output
• DC M6 screw terminals that will allow for large battery cable connection between all sources
• A dedicated Maximum Power Point (MPPT) solar regulator
• The same battery algorithms as included in our AC mains ePOWER battery charger including a specific lithium charging profile
• 40A output up to 40+°C with thermo controlled fan cooling
• Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage
• Temperature sensor included in charger for more accurate battery charging

 *Note: As stipulated by the manufacturer Enerdrive, failure to charge the Enerdrive Lithium Battery range with an Enerdrive or Redarc Lithium Profile battery charger will void Enerdrive manufacturer warranty.

For In Vehicle & Marine Wiring Diagram, click below:

For Towed Vehicle Wiring Diagram, click below:

Enerdrive ePOWER 12V 100A Battery Charger

Enerdrive ePOWER 12V 100A Battery Charger is a fully automatic, “set and forget” charger. It is designed to quickly and accurately recharge your batteries using algorithms that help maximise service life. Multistage smart charging technology enables the charger to be connected to your battery banks permanently.

As dictated by battery manufacturer’s recommendations, batteries require a multistage charge sequence for perfect, fast and accurate charging.

The Enerdrive ePOWER charger can be programmed for Lithium batteries. This setting delivers the full rated output of the charger constantly with the charger switching to power supply mode once the voltage peak is met (indicating a full battery bank).

PRO TIP: Common accessory to go with this Enerdrive 100A AC to DC charger are the 120Amp breakers. It’s available in the Accessory List above to add as optional extras.

100A Battery Charger Features:

• Multistage Charging: Fully automatic multistage battery charger with the ability to charge 3 separate battery banks.
• Separate Battery Banks: Isolated charging design where battery bank one is separate from battery bank two and three.
• Programmable: Battery bank 1 can be programmed with a different charge algorithm over banks 2 and 3.
• Current Control: User adjustable current output (e.g. Dial the 100amp unit back to run off a 1kVA generator).
• Smart Charging: The ePOWER 100A battery charger will regulate its output based on the loads connected to your battery banks.
• Wide AC Input Range: Operates on both 110V / 60Hz and 240V / 50Hz.
• LED Display: Easy to use “set and select” menu along with scrolling charger status.
• Silent Mode: Disables the cooling fan for total silent operation at night or whenever required. Activation reduces charge output by half and locks out fan for 12 hours.
• Temperature Sensor: Battery temperature sensor included with 3 meter cable.
• 5 Year Warranty from an Australian company renowned for customer support.

The Enerdrive ePOWER 2600W 12V Pure Sine Wave

It is a state of the art, easy to use inverter will offer you reliable service for providing AC power for your home, boat, 4WD, truck or Caravan.

The ePOWER 2600W Enerdrive Inverter incorporates a 16A AC Transfer Switch which allows for seamless AC power transfer between Mains/Generator and Inverter. This helps to keep your appliances running with almost no break time on AC transfer and allows for a much simpler installation on-board. This Enerdrive inverter is built to operate basic equipment such as power tools, computers, microwave ovens, televisions and other appliances that use up to 2000W of power for operation.

Features

• Seamless 16A AC Internal Transfer Switch
• AC RCD/Safety Switch with test button
• Removable LED Remote Control Display Panel
• Regulated Pure Sine Wave Output
• Silent Operation
• Compact Size for Easy Installation
• USB Port for charging USB devices
• PS6 Mode
• AC Transfer Cable
• 5 Year warranty

New PS Mode ePOWER Enerdrive Inverters with AC Transfer Switch now include the new PS6 mode. AC Transfer Cable Now Included as Standard Now included with all AC Transfer Switch. Inverters is a 4 metre AC lead with molded Male/Female IEC Plugs fitted. This allows the installer to cut the lead and hardwire the IEC plugs directly. This will speed up installation time and eliminate any connection issues within the plug.  

Simarine Pico+ Display Panel Mount Black

SIMARINE PICO sets new standards for marine battery and tank monitors in 髢ｾ螟ｸ霄ｬlds of design, functionality, connectivity and ease of use.

PICO’s display unit is made of a sleek anodized aluminum casing and a thick Gorilla® Glass with Anti-Reflective coating protecting the optically bonded high-contrast 3.5 inch IPS LCD display. It’s water and dust proof and can be mounted both indoors and outdoors. The screen brightness is automatically adjusted with a light sensor. The device is operated by four water tolerant CapSense® touch buttons.

The Pico system provides you with a simple overview of all important details regarding your battery (voltage, current, amp hours, battery capacity in%, battery temperature) and also tank level and temperature indications.

Simarine Battery Shunt 300A 2 x Volt 2 x Resist 1 x Temp

Innovative combination of Shunt and Tank/Temp level module. The SC303 & SC503 are an active combo shunt for PICO battery monitor with;

• 2 x Voltage Inputs
• 2 x Tank Level or Temperature Inputs
• 1 x Socket for Temperature Sensor with JST connector
• 1 x Current Sensor up to 300A (SC303) or 500A (SC503) for up to 75V systems.

It can be used for monitoring current draw of heavy consumers (inverters, bow and stern thrusters, anchor winches) and current generators (shore power chargers and solar panels). Additionally, it allows monitoring tanks for fuel, fresh and grey water.

Simarine by Enerdrive Quad Shunt Mod 4 x 50A Input Current & 1 x Relay Output 1A

SCQ50 is an innovative shunt module for monitoring individual consumers and generators with;

• 4 x  50A Current Sensors
• For 12v and 24v Systems

Connection Possibilities;

• Up To 4 x Consumer Devices
• Up To 4 x Generators
• Combination of 4 of both
• 1 x Relay Input

.